Sunday, 28 August 2011

28mm Samurai terrain (roadside shrine)

Aha, two posts today? Hell yeah!

Well, I've been off all week with nasty germs and so have had a bit of time (not much though as my wife has been keeping tabs on me) to make things :-)

For the samurai I thought it was about time to make something a bit more than stand alone and so the thought of a roadside shrine to into being.

I wanted to use items that are available from the catalogue just to show what could be possible with a little bit of imagination.

Having come across something similar in Japan it was quite easy to decide the layout which you can see on the right. The figure is an unbased Perry cavalry samurai..

I decided to make the torii from scratch (which they all are) because the ones in the catalogue are already based and I wanted this one integral to the base. Most of these rural shrines have a gravel path leading up to them but I wanted this one to have a disheveled look so some of the border stones are slightly out of place.

This shot shows the final layout and it has also been sanded (sieved builders sand) and covered in thin brown ink. the roof for the moment is separate but everything else is stuck down (a slight mistake on my part but not too troublesome).

Here we have a shot of the basic greenery on the base. I decided to go for three different types of 'growie' for maximum effect and a slightly overgrown appearance.

All the parts were painted in the same way as the catalogue items, I didn't think much point in painting them differently.

The path was drybrushed with various greys and the earth with beiges and tans, building up a nice varied tone throughout.

The growies were added with thinned down white wood glue that was randomly brushed on, the growies being scattered on at three different times, letting each one dry before putting the next one on.

There are a few places where the growies have grown onto the path (hopefully you can see them) and I've also put a few tall grass clumps on just to add to the variation. The trees are old ones from work.

I did think of using some Silfor but it seems everyone is doing it now and I wanted something slightly different. Below we have the beauty shots and there are quite a few because I'm quite pleased with this one :-) I have a few other things of this nature planned but time will tell...




ttfn

And now for something completely similar to what's been done before...

Today's first post is AWI terrain, both n 10mm and 28mm.

First off I was asked to make a small 10mm scale blockhouse in exchange for some goodies by a very nice chap in the LAF.

Well, as I always seem to do, I made it to big :-/ I don't think he'll mind though :-).

It's rather similar in layout to my 28mm blockhouse (picture below) but without the small ancillary building. Simple earth bank and stone base to the blockhouse itself.

The next thing was the stakes in the ground, almost one of the most tedious things I've ever done (but not quite). shaving the top of each one certainly works but when the bloody things are only 1.5mm in diameter it does get a bit much.

Here you can also see the first floor of the blockhouse. this was made from 3/4mm square balsa strip. It's been 'distressed' a bit but not too much as the grain was quite predominant already.

I thought a bit of access would be nice on the inside (even if it's only 10mm) so I made the roof so it could be lift-off-able. There are small feet on the bottom to stop any damage when it's placed on the table top.

You can see here the gate also. I left off the doors because at this scale they would be prone to damage (here's hoping that the gateway itself lasts...).

The next thing I did was to sand over the whole base but I don't have a piccy of that (I think you know what I mean ;-).

And below are a few shots of the finished thing with a shot of the 28mm version for comparison.




The next bit of AWI terrain today is a simple artillery redoubt that could probably be used for a number of conflicts (ECW, AWI, ACW etc).


Simple MDF base, slightly chamfered on the edge. The gabions are my own but the mould is going now so I'll have to make some more masters at some point. They have been raised a bit to look 'right', two have been chopped down also.

Simple foam shapes for the banking covered with cheap wall filler and some balsa scraps for the gun deck.

The whole thing was sanded and given a wash with thinned brown ink. once dry the whole base was drybrushed with various shades of beige and tan.

I decided to put two different types of flock (I normally use static grass) on this to make it look more like real ground as opposed to a gaming table, seems to have worked, bit messy though, I'll be hoovering later :-/ The same ground work was done on the blockhouse above.

On there is my only (for the moment) AWI cannon, British of course but I've got five more of these and about three American ones. I've also got limbers for them as well and one is nearly done :-)


Another shot below and hopefully you can see the flock appearance.


ttfn


Saturday, 13 August 2011

A small generic tug boat

Ah crap, it's been to long. And here I was saying that I would get at least a couple of posts a week down...

Anyway, for tonight's viewing pleasure I have a 28mm Victorian tug boat that I've been meaning to do for a while now. If any of you chaps reading this frequent the Lead Adventure Forum (and if you don't I heartily suggest you do!) you will know that I am doing a Victorian sci-fi force of a Japanese colony on Mars. Many troops and flying things have already been done and will get put up here at some point but I have plenty of civvy things in mind to go with the force and this is one of them.

Basic construction is a blue-foam hull with card and balsa wood decking with a card wheel house and plastic tube for the funnel.

The hull sides are from card and took a while as I had to  bend the card (1.5mm thick) and tape it for a couple of days to let the wood glue go off completely. It's not the best way to do it but I was feeling a bit lazy and wanted to get it done. The card was cut off roughly at the bottom following the blue foam and then I took it into work and took a bit more off the bottom with the bandsaw (it was too high as it was). The edging is microstip.

The rear 'hatch' and stowage box are from sheet styrene and perspex with relevant details from microstrip added (hinges etc.).
The figure is an unknown bobby which is actually a rather nice sculpt and was pleasing to paint.

Other little details were added such as the small sand bucket and the ladders to get to the fore deck. Rivets were glued onto the doors, roof and 'boiler' block to add a bit more of a something. I wanted to keep it simple because I know I can get bogged down in detail and not finish what I started. Fortunately, I think there is enough here to look pleasing and to be playable also.

The shot to the left is of the tug with a coat of Halfords grey primer (one of the best all round primers out there I reckon). If you click on the picture itself you can make out the details better. The canvas roll on the side of the boiler block is from Games Workshops Imperial Guard range from one of the tank kits and have proved useful in the past for various projects.

Next was deciding on the colour scheme, something simple was called for but recognizable as a generic tug. In this Google images was my friend and the next shot shows the basic colour design I went for.

The white strip was painted first and then it was masked out with normal masking tape and a scalpel blade was stuck flat to a block to create a constant level to cut the masking tape around the shape of the hull. When doing this a few light strokes are much better than one heavy one because even tough the blade is stuck down (with superglue) it can still drift off line if you're not careful. The lower portion of the tape was removed and a deep red was painted on the bottom of the hull. When this was dry the process was repeated slightly higher up to create the upper edge of the white band, black was painted above this line and when this was dry the masking was removed to reveal an even white line all the way round the hull.

There were some slight mistakes but I left them on as the tug is a work horse and I didn't think the owner would be too bothered by a sloppy paint job ;-)

The deck was painted with Foundry Palomino light and then given several different brown washes to give some depth to the deck. The wheel house was coated with Foundry Granite and washed with a mix of Devlan mud and Thraka green inks again from GW (some really stupid names for their paints :-/  ). It was then dry-brushed with a light grey I had. The stowage box was painted with a light grey, washed with the above and the touched up with normal white paint.

For the rust I mixed a very watery but bright orange ink and used a fine brush to localise where the rust might form. The main hull was dry-brushed with the same light tan colour used for the deck as I wanted to tie the whole thing together and the windows were given a coat of very dark blue with no high lighting because I don't think it works to well. the funnel was given a band of white but I decided to leave the funnel the same colour as the wheel house instead of doing it in more traditional tug colours (tan, red and black) as it will match my Japanese aeroneff force. The chap on the front is a converted Copplestone Chinese general.

The final shot is of the rear and it shows the details off quite well.

I went around most of the edges with a very dark brown ink just to help emphasize  the shading. The rigging (two pictures above) was simply black thread with a touch of thin superglue to hold it in place and as soon as I can get my dratted printer to work again I will print out a Japanese navel ensign just so we know who's it is :-).

If anyone has any questions (because I've been quite brief) then please leave a comment and I'll get back to you. Thanks for reading (if you managed to get through it all). there will be another small post tomorrow about my Hail Caesar samurai and samurai terrain.

ttfn